How to Install Colorbond Steel Roofings?

Colorbond metal roofing are preferred by many homeowners due to their superior nature and durability. Though installation of Colorbond steel roofs can be done by knowing some DIY roofing techniques, it is advisable to leave things in the hands of a professional.

You get to save a lot of time, energy and reduce exposure to danger as professional handymen get the job done twice as fast. Here are the steps to follow when getting Colourbond steel roofs installed.

Step number one: Install of Gutters and fascias

This is the most basic step to follow when installing Colourbond roofing. A fascia is a long, straight board which runs through the lower edge of the roofing. It supports the lower edge of the bottom row of the roof. Fascias are installed by nailing pre cut boards to the roof frame end.

• To install gutters, you need a measuring tape to know where your outlets are as well as your corners. You also need to know where the drainage pipes are going to be fixed.

• After the measurement is made, you need to cut the gutters. This can be done using a miter saw with a carbide-tipped finish. If you don’t have one, get one.

• After cutting the gutters to length, cut out flaps (to allow for easy attachment at corners) and premeasured holes where drainage pipes can be fixed.

• You then begin the installation. This is done by getting on a ladder and taking your cut gutter with you. It is advisable to keep the centerpiece higher than the rest and use a level to keep the gutter sloping but not noticeable enough.

• Install the end caps using appropriate materials.

• Then use any thermoplastic sealant you can get to seal off ends and corners.

Step two: install sarkings

Also known as roofing foils, sarkings are pliable membranes which are installed under your metal roof and help prevent condensation as well as insulate the rooms underneath. To install sarkings on your roof.

• Cut your sarking according to the size of your roof. It’s advisable to make them extend a little bit past the roof end and into the gutter.

• Nail the sarking shiny face down using the ring shank nails to prevent leakage.

• Continue measuring and nailing until you cover the entire roof.

Step three: Nail the sheets to the reflective foil

The third and final step to installing a Colourbond roof is to nail the metal sheets to the sarking. Having the required materials, you can get to install your metal roofing in no time.

Once installation of the roof is finished, tidying up is the next thing on the agenda. Do make sure to remove all metal shards and used material lying around and make your home the home you want it to be.

To successfully install Colourbond steel roofing, the following supplies are a must-have.

• Roofing nail guns: You need this handy tool to drive nails into joints faster. You might want to have a hammer at hand in case the nail gun gets more encumbering than its worth.
• Roofing hammer or hatchet: A hammer comes in handy when you need to apply nails to fasten metal sheets or sarkings to the frame. It is also the last resort when a roofing nail gun fails.
• Chalk line tools: You need a chalk reel to install open valleys and align gutters.
• Measuring tape or laser tool: The importance of the measuring tape is obviously. Although they are now being replaced with laser tools which measure distances more efficiently and quickly.
• Caulking gun: There are two ways of applying cement onto your roof. Either you use a cement can and trowel or use a caulking gun. The latter allows you more precision and are always preferred over the former.
• Metal snips: This is a good tool to have if you want to cut costs. On the contrary, you can use the motorized shears or drill attachments to save time and make things faster. Metal snips are used to trim edges of metal sheets and also cut gutter material.
• Drill (cordless or air): Drills are an excellent choice when you want to invest in a large air compressor. Getting cordless ones to prevent you from tripping over wires on the roof. Cordless drills have limited battery life. But their convenience during use makes up for their recharging time.

Taking necessary precautions might not be enough to keep accidents at bay. You have to be extra careful when installing Colourbond steel roofs. . You most likely would need the services of a professional colorbond roofing in Sydney one way or another during your DIY installation. Although this is unnecessary if you have all the steps and procedures.